On 7 November 2026, Philippine solar shops listed 4 mm² PV cable at ₱46 to ₱115 a metre, a 2-pole DC breaker at ₱390 and an MC4 connector pair at ₱200. For a typical 8-panel home string, the whole DC and AC protection kit (cable, connectors, breaker, surge protector, isolator and the AC breaker) comes to roughly ₱6,750 in parts. Maliit lang 'yan next to panels and inverter, pero ito ang mga parte na umiinit o nagti-trip kapag mali ang size. So here are the prices, plus the three numbers to check on any quote: cable size, breaker amps and the breaker's DC voltage rating.
Last checked: 7 November 2026. Prices are from the seller pages linked in Sources, on that date. They change often and usually exclude shipping to Leyte or Biliran. Sizing rules are explained so you can check a quote. They don't replace the design and sign-off of a licensed electrical practitioner.
Prices at a glance (7 November 2026)
Part | Seller | Listed price |
|---|---|---|
PV cable 4 mm², single core (Suntree, DC 800V) | Bolinao Solar | ₱46 per m (sale; ₱66 regular) |
PV cable 6 mm², single core (Suntree) | Bolinao Solar | ₱58 per m (sale; ₱83 regular) |
PV cable 4 mm², duplex | Solar Hub PH | ₱80 per m |
PV cable 4 mm², dual core | Letovo | ₱115 per m |
MC4 connector pair | LakaSolar | ₱200 |
DC breaker 2P 16/20/32/63 A, 500V DC | Solar Hub PH | ₱390 (sale; ₱650 regular) |
DC breaker 2P 32 A, 500V DC (Royu) | Felco | ₱390 |
DC breaker 2P 125 A, 500V DC | Solar Hub PH | ₱1,400 (sale; ₱1,950 regular) |
DC surge protector 2P, 600V DC | Solar Hub PH | ₱1,020 |
IP66 DC isolator switch | LakaSolar | ₱2,100 |
AC breaker 2P 40 A | LakaSolar | ₱1,000 |
Battery cable 25 mm², per m | LakaSolar | ₱1,200 |

Buying on Shopee or Lazada? Read our buying guide first. Rails and clamps are itemised in our 5 kW price breakdown and the roof installation guide.
Step 1: Read three numbers off your panel's datasheet
Everything starts from the panel label. Our example is the Jinko Tiger Neo JKM580N-72HL4-BDV (580 W):
Datasheet value | Jinko 580 W |
|---|---|
Short-circuit current, Isc | 13.95 A |
Current at max power, Imp | 13.22 A |
Open-circuit voltage, Voc | 52.50 V |
Voltage at max power, Vmp | 43.88 V |
Voc temperature coefficient | −0.25% per °C |
Maximum series fuse rating | 30 A |
Factory output cable | 4.0 mm² |
Isc sets breaker amps, Voc × panels in series sets breaker voltage, and Imp plus cable length sets voltage drop.
Step 2: Size the DC breaker's amps (the 1.56 × Isc rule)
The Philippine Electrical Code's solar article (6.90) is adapted from the US National Electrical Code's Article 690. The NEC method has two 125% steps: maximum circuit current is 1.25 × Isc, and the breaker or fuse must be rated at least 1.25 times that. Together that's 1.56 × Isc.
Worked example: one string of 580 W panels (Solar Leyte calculation)
- Maximum circuit current: 1.25 × 13.95 A = 17.4 A
- Minimum breaker or fuse rating: 1.25 × 17.4 A = 21.8 A
- Bifacial bonus: Jinko lists Isc 15.25 A with rear-side gain (BNPI). 1.56 × 15.25 A = 23.8 A, still under 25 A.
So what do you buy? It depends on how many strings meet in one place:
- One string per inverter input (most 5 kW homes; the Deye SUN-5K-SG05LP1 takes one string per input). The NEC needs no overcurrent protection when nothing else can feed the string, but Deye's manual still asks for a separate DC breaker, so it acts as your switch. It needs at least 21.8 A and a DC voltage rating above the string's Voc (Step 3). A 32 A DC breaker is fine.
- Three or more strings in parallel (combiner boxes). The others can back-feed one string, so each needs a fuse or breaker between 21.8 A and the panel's 30 A maximum series fuse, which means 25 A. 32 A would be over the panel's limit.
Step 3: Check the DC voltage rating (where cheap breakers fail)
Many DC breakers sold for home solar are rated 500 V DC, including the Solar Hub and Royu listings above. Your string's Voc must stay below that, and below the inverter's limit. The Deye 5 kW hybrid's maximum PV input is also 500 V. Voc rises when panels are cold, by 0.25% for every °C below 25 °C for this panel.
Panels in series | Voc at 25 °C | Voc at 10 °C (our cold margin) | Fits a 500 V breaker and inverter? |
|---|---|---|---|
8 | 420.0 V | 435.8 V | Yes |
9 | 472.5 V | 490.2 V | Only just; ask your installer |
10 | 525.0 V | 544.7 V | No. Needs a higher-voltage inverter and 1000 V DC gear |

The 10 °C cell temperature is our deliberately cold assumption for a safety margin, not a weather forecast. Your installer should use the inverter maker's string calculator.
So a quote that says "10 × 580 W in one string, 500 V DC breaker" has a problem. Tanungin mo: "What's the string Voc, and what DC voltage is the breaker rated for?" Same check for the isolator and surge protector; the 600 V DC SPD above clears an 8-panel string. More in our surge protection guide.
Use breakers marked for DC. A 230 V AC rating says nothing about DC, and Deye's manual specifically calls for a DC breaker on the PV side.
Step 4: Pick 4 mm² or 6 mm² cable
Proper PV cable to the European standard EN 50618 (type H1Z2Z2-K) is rated 1.5 kV DC. Datasheets from Prysmian and Polycab give the same current ratings at a hot 60 °C ambient:
Cable | Single cable, free air | Two cables touching, on a surface | Resistance at 20 °C |
|---|---|---|---|
4 mm² | 55 A | 44 A | 5.09 Ω per km |
6 mm² | 70 A | 57 A | 3.39 Ω per km |
Both are far above our 17.4 A string, so 4 vs 6 mm² is about voltage drop, not overheating. (Deye lists 2.5 mm² as its PV cable size; Jinko's panel leads are 4 mm².)
Worked example: voltage drop on an 8-panel string (Solar Leyte calculation)
String: 8 × 580 W = 4,640 W, working at 351 V and 13.22 A. The current goes up and back, so a 20 m run from roof to inverter is 40 m of cable.
Roof-to-inverter run (one way) | 4 mm² drop | 6 mm² drop | Watts lost at full sun, 4 vs 6 mm² |
|---|---|---|---|
10 m | 0.38% | 0.26% | 18 W vs 12 W |
20 m | 0.77% | 0.51% | 36 W vs 24 W |
30 m | 1.15% | 0.77% | 53 W vs 36 W |
40 m | 1.53% | 1.02% | 71 W vs 47 W |
These use the 20 °C resistance; cable baking on a tin roof is about 27% more resistive at 90 °C (electrice datasheet), so real losses run a bit higher. Forty metres of the Suntree cable is ₱1,840 in 4 mm² or ₱2,320 in 6 mm², just ₱480 more. For long runs, 6 mm² is cheap insurance.

Read the jacket: the Suntree listing says DC 800V, not EN 50618's 1.5 kV. Enough for 8 panels, but a different product. And 12V or 24V kits carry far more current for the same watts, so they need thicker cable; see our 12V vs 24V vs 48V guide.
Step 5: MC4 connectors, don't mix brands
MC4 pairs are cheap (₱200 above), but Stäubli, maker of the original MC4, says connectors from different manufacturers shouldn't be mated, since certification covers matched pairs only. Ask for the same make on both halves of every joint, crimped with a proper MC4 tool (LakaSolar lists one at ₱1,500), not pliers. Near the sea, see our salt-air guide.
The battery and AC side, briefly
- Battery. Deye's 5 kW hybrid takes up to 120 A, with a 35 mm² (1 AWG) cable and a separate DC over-current protector. The 25 mm² cable above is Deye's size for the 3.6 kW model, not the 5 kW. A 125 A DC breaker (₱1,400) is the kind of part used, but battery protection is a licensed electrician's call.
- AC side. Deye recommends 40 A AC breakers on the grid and backup-load sides of its 3.6–6 kW models, certified to IEC 60947-1 and -2. LakaSolar's 2-pole 40 A is ₱1,000.
Worked example: the parts bill for an 8-panel string (Solar Leyte calculation)
Part | Quantity (our estimate) | Price used | Subtotal |
|---|---|---|---|
4 mm² PV cable (Suntree, Bolinao Solar) | 40 m | ₱46 per m | ₱1,840 |
MC4 connector pairs (LakaSolar) | 2 | ₱200 | ₱400 |
DC breaker 2P 32 A, 500 V DC (Royu, Felco) | 1 | ₱390 | ₱390 |
DC SPD 600 V (Solar Hub PH) | 1 | ₱1,020 | ₱1,020 |
IP66 DC isolator (LakaSolar) | 1 | ₱2,100 | ₱2,100 |
AC breaker 2P 40 A (LakaSolar) | 1 | ₱1,000 | ₱1,000 |
Total, parts only | ₱6,750 |
Not included: enclosure, conduit, grounding, labels, battery parts, shipping and labour. Ask for each part by brand and rating in the quote; our contract checklist shows how.
Who should do the wiring?
You can buy the parts, but under RA 7920 electrical work is for licensed practitioners, and the electrical permit and CFEI from your town hall come first. See our installer checklist and permit and CFEI guide. For the full system budget, start from our solar panel price guide.
FAQ
Magkano ang solar cable per meter sa Pilipinas?
On 7 November 2026: ₱46 (4 mm²) and ₱58 (6 mm²) a metre for Suntree single core at Bolinao Solar on sale, ₱80 for 4 mm² duplex at Solar Hub PH and ₱115 for 4 mm² dual core at Letovo.
What size DC breaker for a 550 W or 600 W solar panel?
Take the panel's Isc and multiply by 1.56. For a 580 W Jinko with 13.95 A Isc that's 21.8 A. One string per inverter input can use a 32 A DC breaker as its switch. Paralleled strings need 25 A, which is under the panel's 30 A fuse limit. Also check that the DC voltage rating is above the string's Voc.
Pwede bang 4 mm² lang sa 5 kW system?
Usually yes for the panel strings. 4 mm² carries 55 A in free air, and the loss on a 20 m run is about 0.8% in our example. Go 6 mm² for long runs. The battery cable is a different story: Deye lists 35 mm² for its 5 kW hybrid.
Can I use an AC breaker on the solar panel side?
No. Use a breaker marked for DC with a DC voltage rating above your string Voc, as Deye's manual asks.
Solar Leyte is run by MACC Systems & Energy Solutions Inc., a solar installer in Naval, Biliran.
Get a free solar quote from MACC
Want a parts list where every cable, breaker and connector is sized to your panels and inverter? Send us your latest BILECO or LEYECO bill and a photo of your roof, and we'll get back to you with a free, no-obligation written quote.
- Call/Text: 0955 723 5093
- Email: official@macc-inc.com
- Website: www.macc-inc.com
Sources (all checked 7 November 2026)
- Cable prices: Bolinao Solar, Suntree single core PV cable 4/6 mm² per metre (₱46 / ₱58 sale; ₱66 / ₱83 regular; AC 1000V DC 800V); Solar Hub PH, 4 mm² duplex PV cable (₱80); Letovo, PV cable 4 mm² dual core (₱115)
- Breakers and protection: Solar Hub PH, 32 A DC breaker 2P (₱390, DC 500V; same price for 16 A, 20 A and 63 A), 125 A DC breaker 2P (₱1,400) and DC SPD 2P 600V (₱1,020); Felco, Royu DC MCB 2P 32A 500VDC (₱390)
- LakaSolar: MC4 connector pair (₱200), MC4 crimping tool (₱1,500), IP66 DC isolator (₱2,100), AC 2P breaker 40A (₱1,000), 25 mm² battery cable (₱1,200 per metre)
- Panel data: Jinko Solar, JKM575-600N-72HL4-BDV datasheet (PDF) (580 W: Isc 13.95 A, Imp 13.22 A, Voc 52.50 V, Vmp 43.88 V, Voc −0.25%/°C, BNPI Isc 15.25 A, max series fuse 30 A, 4.0 mm² leads)
- Inverter data: Deye, SUN-3.6–8K-SG05LP1-EU user manual (PDF, 19 March 2026) (separate DC breaker before PV input; PV cable 2.5 mm² / 12 AWG; max PV input 500 V; 1+1 strings on the 5 kW; 5 kW battery 120 A and 35 mm² / 1 AWG, 3.6 kW 25 mm²; separate battery over-current protector; 40 A AC breakers, IEC 60947-1/-2)
- Breaker sizing: Mike Holt, Solar Photovoltaic Systems, based on the 2017 NEC, Part 1 (690.8 maximum current 125% of Isc; 690.9 overcurrent device ≥125% of that; exception when there are no external sources); Mersen, Sizing fuses for PV systems per NEC (PDF); IAEI Magazine, Inspectors demand more answers (1.56 × Isc; one or two strings usually need no string fuse; three or more need a calculation)
- Philippine code: Filipino Engineer wiki, PEC 2017 Part 1, Article 6.90 Solar Photovoltaic (PV) Systems_Systems) (scope)
- Cable data: Prysmian, PRYSUN H1Z2Z2-K datasheet and Polycab, Solar H1Z2Z2-K EN 50618 (PDF) (1.5 kV DC; 4 mm² 55 A / 44 A, 6 mm² 70 A / 57 A at 60 °C ambient; 5.09 and 3.39 Ω/km at 20 °C); electrice, H1Z2Z2-K technical data sheet (PDF) (6.49 Ω/km for 4 mm² at 90 °C)
- Connectors: Stäubli, Avoid cross-mating: only link same-manufacturer PV connectors
- Law: RA 7920, New Electrical Engineering Law (Lawphil)
- Voltage-drop, Voc and parts totals are Solar Leyte calculations from the figures above.
